100% Pass Guaranteed Accurate JN0-452 Answers 365 Days Free Updates
JN0-452 DUMPS Q&As with Explanations Verified & Correct Answers
NEW QUESTION # 61
You are deploying three WLAN 2.4 GHz networks in your US-based site. You must ensure that each network frequency is unique and does not overlap with the other frequency channels.
In this scenario, which three OFDM channels should be used? (Choose three.)
- A. 0
- B. 1
- C. 2
- D. 3
- E. 4
Answer: B,C,E
NEW QUESTION # 62
All the access points (APs) on the site will obtain an IP address for the Management VLAN.
You notice an additional IP address for each configured VLAN on the AP.
Which statement is correct in this scenario?
- A. This behavior is enabled by default under the Site configuration.
- B. The AP is configured to support wireless mesh.
- C. The AP MAC has a DHCP reservation.
- D. The Local Status Page has been enabled in the AP setting under the Site configuration.
Answer: A
NEW QUESTION # 63
An administrator wants to use a single WLAN template for multiple sites. The corporate SSID is the same everywhere, but the guest SSID name needs to be unique for each site (e.g., "BranchA- Guest", "BranchB-Guest").
How can this be achieved using a single WLAN template?
- A. Create a Device Profile for each site and define the guest SSID name within the profile.
- B. In the WLAN template, create the guest WLAN and use a variable like `{{site_name}}-Guest` in the SSID field.
- C. It cannot be done; a separate WLAN template is required for each site.
- D. Use a WxLAN policy to dynamically change the SSID name based on the client's location.
Answer: B
NEW QUESTION # 64
You want to review the roaming activity of a specific wireless client. In this scenario, which two Marvis features would you use to accomplish this task? (Choose two.)
- A. Marvis Query Language
- B. Marvis Minis
- C. Marvis Virtual Network Assistant
- D. Marvis Actions
Answer: A,C
Explanation:
To review the roaming activity of a specific wireless client, you would use Marvis Query Language (MQL) or interact with the Marvis Virtual Network Assistant (VNA). Both provide client-level insights, including connection history and roaming events, enabling detailed troubleshooting of client mobility.
NEW QUESTION # 65
An administrator is deploying a new Mist network in a dense office environment and wants to ensure that client devices with poor signal strength do not negatively impact airtime for other users. Which two actions should be taken in the RF Template to enforce a higher minimum performance standard? (Choose 2.)
- A. Enable "Band Steering" to encourage clients to use the 5 GHz band.
- B. Disable the lower legacy data rates (e.g., 1, 2, 5.5, 6, 9, 11 Mbps).
- C. Set a minimum RSSI threshold using the Geofencing feature.
- D. Increase the DTIM period to a higher value.
- E. Increase the AP's transmit power to the maximum level.
Answer: A,B
NEW QUESTION # 66
Your customer added an Apple TV in their conference room so that employees can easily share their screen.
However, the Apple TV cannot be discovered by the employees' devices.
Which two settings are causing the problem? (Choose two.)
- A. Ignore Broadcast SSID Probe Requests
- B. ARP
- C. MDNS
- D. Broadcast/Multicast
Answer: C,D
Explanation:
If a customer added an Apple TV in their conference room so that employees can easily share their screen but the Apple TV cannot be discovered by the employees' devices, two settings that could be causing this problem are MDNS and Broadcast/Multicast. So the correct answers are A. MDNS and B. Broadcast
/Multicast.
NEW QUESTION # 67
You are asked to find the location of a BLE client. In this scenario, what is the required Juniper Mist license subscription service?
- A. User Engagement
- B. Wireless Assurance
- C. Wired Assurance
- D. Asset Visibility
Answer: D
Explanation:
In the Juniper Mist location framework, BLE-based location tracking maps to the Asset Visibility subscription (SUB-AST). This service is what enables the location engine to detect, place, and track BLE devices/tags on the indoor map, including named assets and zones.
NEW QUESTION # 68
Click the Exhibit button.
Referring to the exhibit, which client has the weakest connection to the WLAN?
- A. Client 3
- B. Client 2
- C. Client 1
- D. Client 4
Answer: C
Explanation:
Client 1 shows an RSSI of -81 dBm and an SNR of 11 dB, both of which indicate a much weaker connection compared to the other clients. Lower RSSI (closer to -100 dBm) and low SNR mean poor signal strength and higher interference, resulting in the weakest WLAN connection.
NEW QUESTION # 69
Which two SLE classifiers would indicate that a client is having a good roaming experience?
(Choose two.)
- A. Slow 11r Roams
- B. Interband Roam
- C. Sticky Client
- D. Failed to fast Roam
- E. Suboptimal Roam
Answer: B,C
NEW QUESTION # 70
Which two statements are true about Distributed Coordination Function (DCF)? (Choose two.)
- A. The station can only transmit when the RF medium is free.
- B. If the station can hear another 802.11 transmission on the channel, it will transmit immediately.
- C. If the station detects a collision at any point, it transmits immediately.
- D. The station waits to transmit between frames for the interframe spacing.
Answer: A,D
Explanation:
Distributed Coordination Function uses carrier sense multiple access with collision avoidance, so a station must wait the required interframe spacing and can transmit only when the RF medium is determined to be free.
NEW QUESTION # 71
An administrator is configuring a WLAN for a high-density environment. To improve overall network performance and free up airtime, they want to disable support for the oldest and slowest Wi-Fi standard. Which standard operates in the 2.4 GHz band and uses DSSS modulation with a maximum data rate of 11 Mbps?
- A. 802.11n
- B. 802.11b
- C. 802.11a
- D. 802.11g
Answer: B
NEW QUESTION # 72
Which statement is true about how RF Templates, Device Profiles, and individual AP settings are applied?
- A. Device Profile settings override all other settings.
- B. RF Template settings always have the highest priority.
- C. Settings are merged, and the most restrictive setting is applied.
- D. Individual AP settings override Device Profile settings, which override RF Template settings.
Answer: D
NEW QUESTION # 73
A hospital wants to track the location of its high-value medical equipment, which has been tagged with BLE asset tags.
Which Mist LBS feature is designed for this use case?
- A. Wi-Fi Location
- B. User Engagement
- C. Proximity Tracing
- D. Asset Visibility
Answer: D
NEW QUESTION # 74
Click the Exhibit button.
Referring to the exhibit, what would a guest user be able to do?
- A. Use the Internet, except for Gmail and Slack.
- B. Use the HP Printer and Internet.
- C. Use Gmail and Slack.
- D. Use only the Intranet.
Answer: A
Explanation:
A firewall is a network security system that monitors and controls incoming and outgoing network traffic based on predetermined security rules. It typically establishes a barrier between a trusted internal network and an untrusted external network, such as the Internet .
NEW QUESTION # 75
Click the Exhibit button.
Referring to the exhibit, which percentage of connection attempts failed on the access point named LD_RS_Support?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: B
Explanation:
The 37% of Successful Connects suggest that 63% failed - however, these are spread between both LD_Testbed_MD and LD_RS_Support. If the only AP with connection issues was LD_RS_Support then the reverse math may have worked.
NEW QUESTION # 76
Your organization has recently purchased new VoIP handsets. All of the VoIP handsets fail to connect to the corporate WLAN. However, all other devices connect successfully. You expect that there might be a bug with the new handsets. The vendor asks you to provide a pcap file of the handsets' connection attempts.
Which Juniper Mist feature will provide this file?
- A. Clients Insights
- B. Alerts dashboard
- C. Service Level Expectations
- D. Dynamic Packet Capture
Answer: D
NEW QUESTION # 77
A client calls you to troubleshoot possible interference with your wireless network. Before you drive to the customer's site to investigate, you want to quickly verify if there is actually any interference at all. In this scenario, which SLE is responsible for this interference?
- A. roaming
- B. coverage
- C. capacity
- D. throughput
Answer: C
Explanation:
The Capacity Service Level Expectation (SLE) in Juniper Mist is specifically designed to monitor the health of the RF environment. It tracks how much "airtime" is available for clients and identifies factors that are consuming that airtime.
When you drill down into the Capacity SLE, it provides specific classifiers (sub-metrics) that identify interference:
Non-WiFi Interference: Detects energy from non-802.11 sources like microwaves, Bluetooth devices, or wireless cameras.
WiFi Interference (Co-Channel Interference): Measures the impact of other nearby Access Points operating on the same channel.
NEW QUESTION # 78
A university wants to provide basic Internet access to visitors in their library. The access should not require a password but must direct users to a page where they accept the terms of use before connecting.
What type of guest WLAN should be configured?
- A. WPA2 with a shared Pre-Shared Key
- B. WPA3-Enterprise with 802.1X
- C. Open Access with Captive Portal (Splash Page)
- D. External Captive Portal
Answer: C
NEW QUESTION # 79
Which real-time location system component takes the coordinates of a tracked device and applies a location- aware triggered action to a client?
- A. Juniper Mist Edge
- B. location system
- C. Marvis Minis
- D. location sensor
Answer: B
Explanation:
In the architecture of aMist AI Real-Time Location System (RTLS), the process of moving from raw signal data to an actionable event involves several distinct layers. To understand why thelocation systemis the correct answer, we must examine how Mist processes Location-Based Services (LBS).
The workflow begins withlocation sensors(typically Mist Access Points). these sensors collect raw Bluetooth Low Energy (BLE) or Wi-Fi signals (RSS measurements) from tracked assets or mobile devices. These raw data points are then transmitted to the cloud-basedMist AI engine. Thelocation system(often referred to as the Location Engine within the Mist Cloud) is the specific functional component responsible for calculating the precise X/Y coordinates of the device using machine learning and trilateration algorithms.
However, its role does not end at mere coordinate calculation. The Mist location system is designed to be
"context-aware." Once the coordinates are established, the system maps these coordinates against defined zones, virtual beacons (vBeacons), or geofencesconfigured in the Mist dashboard. When a device's coordinates intersect with a predefined boundary, the location system triggers alocation-aware action. This could include sending a webhook to a third-party application, pushing a proximity notification to a mobile SDK client, or recording a "visit" in the analytics engine.
WhileJuniper Mist Edgehandles data plane tunneling andMarvis Minisacts as a digital twin for network simulation, they do not manage the coordinate-to-action logic. Thelocation systemis the intelligence that bridges the gap between spatial data and business logic, ensuring that the right client receives the right trigger based on their physical presence within a venue.
NEW QUESTION # 80
Which real-time location system component takes the coordinates of a tracked device and applies a location- aware triggered action to a client?
- A. Juniper Mist Edge
- B. location system
- C. Marvis Minis
- D. location sensor
Answer: B
Explanation:
In the architecture of a Mist AI Real-Time Location System (RTLS), the process of moving from raw signal data to an actionable event involves several distinct layers. To understand why the location system is the correct answer, we must examine how Mist processes Location-Based Services (LBS).
The workflow begins with location sensors (typically Mist Access Points). these sensors collect raw Bluetooth Low Energy (BLE) or Wi-Fi signals (RSS measurements) from tracked assets or mobile devices.
These raw data points are then transmitted to the cloud-based Mist AI engine. The location system (often referred to as the Location Engine within the Mist Cloud) is the specific functional component responsible for calculating the precise X/Y coordinates of the device using machine learning and trilateration algorithms.
However, its role does not end at mere coordinate calculation. The Mist location system is designed to be
"context-aware." Once the coordinates are established, the system maps these coordinates against defined zones, virtual beacons (vBeacons), or geofences configured in the Mist dashboard. When a device's coordinates intersect with a predefined boundary, the location system triggers a location-aware action. This could include sending a webhook to a third-party application, pushing a proximity notification to a mobile SDK client, or recording a "visit" in the analytics engine.
While Juniper Mist Edge handles data plane tunneling and Marvis Minis acts as a digital twin for network simulation, they do not manage the coordinate-to-action logic. The location system is the intelligence that bridges the gap between spatial data and business logic, ensuring that the right client receives the right trigger based on their physical presence within a venue.
NEW QUESTION # 81
......
JN0-452 dumps Exam Material with 137 Questions: https://www.actualcollection.com/JN0-452-exam-questions.html
JN0-452 Questions and Answers Guarantee you Oass the Test Easily: https://drive.google.com/open?id=1dAiNrtfmwsFT42vqL9CMl6UIrhMcRRAB