Pass Exam Questions Efficiently With 300-510 Questions (2024)
300-510 Questions - Truly Beneficial For Your Cisco Exam
Cisco 300-510 certification exam covers a wide range of topics related to advanced routing solutions in a service provider network, including BGP, OSPF, IS-IS, MPLS, segment routing, EVPN, and VRF. 300-510 exam is designed to test the candidate's ability to design, configure, and troubleshoot these routing protocols and technologies in a service provider environment.
NEW QUESTION # 17
Compare different features between OSPFv2 and OSPFv3. Drag and drop the descriptions of OSPF from the left onto the correct OSPF versions on the right.
Answer:
Explanation:
NEW QUESTION # 18
Refer to the exhibit. MPLS traffic from the packet core that is connected to router RX (10.10.10.1) to the radio network that is connected to router RB (10.10.10.6) uses the longer route RB R2 RY RX RX and R2 are configured with a default value of LDP hello and hold intervals. The team verified that OSPF neighborship in Area 0 is established between RX and R2.
Which action must be taken to choose the shortest path and resolve the issue?
- A.
- B.
- C.
- D.
Answer: C
NEW QUESTION # 19
Refer to the exhibit.
Routers RA and RB are IS-IS peers configured for NSF but router RC is an IS-IS peer without NSF capability If RA undergoes processor switchover what is the effect on the network environment?
- A. All peer relationships remain up, but the link-state database is rebuilt on each device
- B. If RC is operating without the Cisco configuration option only 2 routers tear down their peering relationships and re-establish peering
- C. All peer relationships remain up and the link-state database is unchanged
- D. If RC is operating without the Cisco configuration option all three routers tear down their peering relationships and re-establish peering
Answer: A
NEW QUESTION # 20
Refer to the exhibit.
R3 is:
failing to accept multicast RP information from Domain-A
advertising MSDP SA messages to R1 and R4
receiving SA messages only from R4
Which command must the engineer implement to resolve the issue?
- A. R3# ip msdp sa-filter out 192.168.1.1
- B. R3# ip msdp sa-filter in 192.168.3.1
- C. R3# no ip msap sa-filter in 192.168.1.1
C R3# no ip msdp peer 192.168.1.1
Answer: C
NEW QUESTION # 21
Refer to the exhibit. The four routers in this network have formed adjacencies. Router R2 is an IS- IS level 1-2 router that connects to other areas, and the attach bit is set in the R2 level 1 LSP advertisements to R1. According to the network design, R2 should push level 2 routes from its routing table to the R1 routing table. However, R1 installed a default route in its routing table.
Which action resolves this problem?
- A. Use the is-type level-1-2 backdoor command to unset the attach bit on R1 and use a prefix list to filter prefixes from R2.
- B. Set the attach bit on R1 and use a prefix list to filter prefixes from R2.
- C. Configure R2 as a level 1 router and use a prefix list to filter prefixes to R1
- D. Use the is-type level-1-2 backdoor command to unset the attach bit on R2 and configure a distribute-list to redistribute prefixes to R1.
Answer: D
NEW QUESTION # 22
An engineer is troubleshooting end-to-end customer traffic across an MPLS VPN service provider network.
Which tasks should the engineer use to solve the routing issues? Drag and drop the table types from the left onto the most useful troubleshooting tasks/router types on the right. (Not all options are used.)
Answer:
Explanation:
NEW QUESTION # 23
Refer to the exhibit. Traffic flow from router R1 to router R6 is delay-sensitive. It must consider potential link-failure and node-failure conditions.
Which configuration must an engineer apply to router R1 to route traffic to router R6 if router R2 fails?
- A. Option B
- B. Option C
- C. Option A
- D. Option D
Answer: A
NEW QUESTION # 24
Refer to the exhibit. Router 1 is connected to router 2 on interface TenGigE0/1.
Which interface provides the alternate path to 172.16.200.9/32 when the link between router 1 and router 2 goes down?
- A. TenGigE0/2 interface provides the alternate path
- B. A primary path must be manually installed
- C. A backup path must be statically installed
- D. TenGigE0/1 interface provides the alternate path
Answer: A
NEW QUESTION # 25
Refer to the exhibit.
A network engineer implemented this segment routing configuration. Which statement about the output is true?
- A. A nondefault segment routing global block range is being used on this device.
- B. The default segment routing global block range is being used on this device.
- C. This range conflicts with the segment routing local block range.
- D. The device must be reloaded for these ranges to be allocated and used.
Answer: A
Explanation:
Reference:
segment-routing-book/seg-routing-global-block.html
NEW QUESTION # 26
Refer to the exhibit.
A network engineer applied configuration on R1 to summarize all ISIS routes, but R2 Is still receiving specific routes from R1. The engineer has confirmed that both routers are configured with the correct summarization configuration, but R1 is not sending the correct summary routes. Which configuration must be applied to router R1 to summarize routes within Level 1?
- A. R1(config-router)#summary-address 1.0.0.0 255.0.0.0 level-1
- B. R1(config-router)#no summary-address 1.0.0.0 255.0.0.0 level-1
- C. R1(config-router)#summary-address 1.0.0.0 255.0.0.0 level-2
- D. R1 (config-router)#summary-address 1.0.0.0 255.0.0.0 level-1-2
Answer: A
NEW QUESTION # 27
Which statement about BFD on Cisco IOS XR Software is true?
- A. Cisco IOS XR Software does not support BFD multihop for IPv4.
- B. Cisco IOS XR router must use dynamic routing or a static route back to the Cisco IOS router to establish the peer relationship.
- C. Cisco IOS XR router must use LDP to route back to the Cisco IOS router to establish the peer relationship.
- D. BFD is not compatible between Cisco IOS XR and Cisco IOS Software.
Answer: B
NEW QUESTION # 28
Refer to the exhibit.
Router 1 has attempted to establish a Cisco MPLS TE tunnel to router 2, but the tunnel has failed. Which statement about this configuration is true?
- A. Router 2 must have a tunnel interface created with router 1 as the destination
- B. Router 1 and router 2 must define the RSVP bandwidth reserved on the physical interfaces
- C. Router 1 must define an explicit path to router 2
- D. Router 1 must have Cisco MPLS TE enabled on interface gigabitethernet0/1
Answer: D
NEW QUESTION # 29 
Refer to the exhibit. Routers R1 and R2 cannot form a neighbor relationship, but the network is otherwise configured correctly and operating normally. Which two statements describe the problem? (Choose two.)
- A. The two routers are in different subnets
- B. The two routers have password mismatch issues
- C. The two routers have the same network ID
- D. The two routers are in the same area
- E. The two routers are in different areas
Answer: A,E
NEW QUESTION # 30
Refer to the exhibit.
Routers R1, R2. R3, and R4 have been configured to run OSPF. and router R5 is running EIGRP Traffic from R1 to R5 is expected to pass via R4. but OSPF routing has calculated the best path via R3. Which action corrects the problem?
- A. Configure R3 to use metric-type 1 with a higher metric than R4.
- B. Reconfigure R1 in Area 0.
- C. Change the metric-type value on R3 to 2.
- D. Configure R1 with a static route to the R5 networks and set R5 as the next hop.
Answer: C
NEW QUESTION # 31
Refer to the exhibit. A network engineer installed a new router (Router 3) at the regional hub running MPLS services for scalability. Router 3 is connected to the 10.44.4.0/24, 10.44.5.0/24,
10.44.6.0/24, and 10.44.7.0/24 subnets. The new router has been configured for OSPF Area 2, and it is advertising the four connected networks. The engineer noticed that the same networks are listed as interarea summary routes, and they are being flooded into each area on the area borders. Which action resolves the issue?
- A. Under the OSPF configuration on router 3, add area 2 range 10.44.4.0 255.255.252.0.
- B. On router 2, configure a route map to filter the networks.
- C. On router 3, configure an access list to filter the networks.
- D. Under the OSPF configuration on router 2, add area 2 range 10.44.4.0 255.255.252.0.
Answer: D
NEW QUESTION # 32
Which two differences should be considered when deciding whether to implement to implement routing policies or route maps? (Choose two.)
- A. Route policies require sequence numbers, but route maps are implemented without sequencing.
- B. Route maps are supported in Cisco 10S Software and routing policies are supported in Cisco IOS XR Software.
- C. Route maps require an explicit deny at the end of the sequence, but routing policies have an implicit deny at the end of the program.
- D. Sequences are added after implementing a route map, but routing policies must be reconfigured when change is needed.
- E. Route maps are implemented using hierarchical policies, but routing policies must be implemented sequentially.
Answer: B,D
NEW QUESTION # 33
Refer to the exhibit. XR1 and XR2 are sending the prefix 10.11.11.0/24 to XR3.
A configured policy on XR1 is incorrectly prepending AS path 11 11 12 12 onto this prefix.
A network operator wants to add a policy onto XR3 that will not allow the falsely prepending prefix from being installed.
Which policy configuration applied to the XR3 neighbor configuration for XR1 can accomplish this requirement without impact to other or future received routes?
- A. Option B
- B. Option D
- C. Option C
- D. Option A
Answer: B
Explanation:
https://www.cisco.com/c/en/us/td/docs/routers/crs/software/crs_r4-
1/routing/command/reference/b_routing_cr41crs/b_routing_cr41crs_chapter_01000.html#wp3850
885229
NEW QUESTION # 34
Refer to the exhibit.
After these configurations were applied to routers R1 and R2. the two devices cannot form a neighbor relationship What is the reason tor the problem?
- A. The two routers cannot authenticate with one another
- B. The two routers have the same network ID
- C. The two routers have different iS-types
- D. The two routers have the same area ID.
Answer: A
NEW QUESTION # 35
Compare different features between OSPFv2 and OSPFv3. Drag and drop the descriptions of OSPF from the left onto the correct OSPF versions on the right.
Answer:
Explanation:
NEW QUESTION # 36
Refer to the exhibit. Customer traffic from the branch site to the hub is experiencing packet drops.
The engineer verified that:
- Customer traffic from the hub is able to reach the branch site.
- The connection between PE1 and PE2 is working normally.
- Routers P1 and P2 are able to ping devices on the hub site.
Which action resolves the issue?
- A. Redistribute the CE2 OSPF routes in the PE2 VRF.
- B. Advertise the VPNv4 routes of the branch site in CE2.
- C. Advertise the VPNv4 routes of the hub in CE1.
- D. Redistribute the CE1 OSPF routes in the PE1 VRF.
Answer: C
NEW QUESTION # 37
Refer to the exhibit.
The extension header of the IPv6 header is ignored when which value is equal to zero?
- A. Hdr Ext Len
- B. Next Header
- C. Routing Type
- D. Segments Left
Answer: B
NEW QUESTION # 38
An engineer is troubleshooting a connectivity issue across the MPLS network and is verifying the forwarding behavior of packets.
Which table does the engineer look at to verify the forwarding behavior of an IP packet as it enters the MPLS network at the ingress LSR?
- A. FIB
- B. RIB
- C. LFIB
- D. LIB
Answer: C
NEW QUESTION # 39
......
Cisco 300-510 certification exam is a challenging but rewarding opportunity for IT professionals who want to showcase their skills and knowledge in implementing advanced routing solutions within service provider networks. By earning this certification, candidates can enhance their career prospects, gain industry recognition, and contribute to the success of their organizations by ensuring the efficient and effective delivery of services over service provider networks.
Cisco 300-510 certification exam is designed to test the skills and knowledge of IT professionals in implementing and troubleshooting advanced routing solutions for service providers. Implementing Cisco Service Provider Advanced Routing Solutions certification is ideal for professionals who are looking to advance their careers in the field of networking and want to specialize in service provider routing solutions. 300-510 exam covers a range of topics including advanced routing protocols, VPN technologies, MPLS, segment routing, and network automation.
Truly Beneficial For Your Cisco Exam: https://www.actualcollection.com/300-510-exam-questions.html
Download Cisco 300-510 Sample Questions: https://drive.google.com/open?id=1CtAQdA4AjhebFGxBD7aXpLFsmBBs6twL