Tested Material Used To NS0-176 Test Engine Exam Questions in here [Nov-2021]
Penetration testers simulate NS0-176 exam PDF
NetApp NS0-176 Exam Topics:
| Section | Objectives |
|---|---|
| FlexPod Troubleshooting | - Demonstrate how to perform FlexPod troubleshooting |
| Information Gathering for FlexPod Solutions | - Describe the main FlexPod components |
| FlexPod Configuration | - Describe how to install and configure the FlexPod components - Describe how to configure neworks in a UCS solution - Describe how to configure SAN boot in a FlexPod solution - Describe knowledge of how to configure a service profile - Demonstrate knowledge of how to configure storage in a FlexPod solution - Demonstrate knowledge of how to configure Cisco Nexus switches |
| FlexPod Administration | - Demonstrate knowledge of how to administer FlexPod solutions according to FlexPod best practices - Describe FlexPod management applications - Demonstrate knowledge of how to install and upgrade the FlexPod solution |
| FlexPod Design | - Describe the storage components supported in FlexPod - Describe the networking components supported in FlexPod - Describe the compute components supported in FlexPod |
NEW QUESTION 72
Which two are true about Fabric Interconnect L1 and L2 ports in cluster mode? (Choose two)
- A. Ports can run as a port channel or as individual links
- B. Ports can only run as individual links
- C. Ports are primarily used for management traffic, but can be used for data traffic as well
- D. Fabric Interconnects connected via L1/L2 have to be the same model except during the upgrade
- E. Fabric Interconnect ports L1 and L2 are 10 Gb links
- F. Ports can only run as a port channel
Answer: D,F
NEW QUESTION 73
A Cisco UCS system is operating in FC End-Host Mode. The fabric Interconnects are uplinked into Nexus 5672UP switches using native FC. The service profiles are unable to boot from SAN using FC.
When executing the show flogi database command on the Nexus switches, only the Fabric Interconnect port WWNs are visible. No service profile WWNs are shown.
What caused this issue?
- A. The zoning on the Nexus switches is incorrect.
- B. The Nexus switches do not have NPIV enabled.
- C. The Nexus must be configured for FCoE instead of native Fibre Channel.
- D. The Nexus switches do not have NPV enabled.
Answer: B
NEW QUESTION 74
Exhibit:
Your vSphere host is booting off an SD and is displaying the error shown in the exhibit.
What should you do to correct the problem?
- A. Enable Unified Extensible Firmware Interface (UEFI).
- B. Update the current ESXi scratch location.
- C. Reinstall ESXi on a larger SD card.
- D. Enable SD card mirroring.
Answer: B
NEW QUESTION 75
Your company is looking for a small remote office infrastructure to deploy to your 30 remote sites. You are asked to write deployment procedures for each site. Your goal is to have each site deployed in less than a day.
Which tool will help you accomplish your goal?
- A. OnCommand Insight
- B. UCS Director
- C. OnCommand System Manager
- D. UCS Manager
Answer: B
NEW QUESTION 76
You are asked to create an interface group on a NetApp clustered Data ONTAP system. The system is connected to a Cisco Nexus switch in a vPC configuration with the port-channel mode set to active.
Which NetApp interface group made matches this switch configuration?
- A. multimode
- B. singlemode
- C. multimode_lacp
- D. mode active
Answer: B
NEW QUESTION 77
How many ACTIVE SPAN sessions exist on a Fabric Interconnect?
- A. 0
- B. 1
- C. 2
- D. 3
- E. 4
Answer: C
NEW QUESTION 78
You are installing a FlexPod Express solution with a NetApp AFF A250 at a customer's remote site.
In this scenario, which two devices are required to provide an NFS v3 datastore? (Choose two.)
- A. NetApp BES-53248 Switches
- B. Cisco UCS 6324 Fabric Interconnects
- C. Cisco UCS 6454 Fabric Interconnects
- D. Cisco Nexus 3000 Switches
Answer: B,D
NEW QUESTION 79
Which feature allows Cisco Nexus 7000 Series switches to be virtualized at the device level?
- A. VRF
- B. PONG
- C. VDC
- D. VLAN
Answer: C
NEW QUESTION 80
How many cluster interconnect switch(es) are required for a 4-node NetApp cluster?
- A. 0
- B. 1
- C. 2
- D. 3
- E. 4
Answer: C
NEW QUESTION 81
Which two features allow multiple fabric logins through a single port? (Choose two.)
- A. NPV
- B. vPC
- C. LLDP
- D. NPIV
Answer: A,D
NEW QUESTION 82
You are asked to verify your MPIO settings for your ONTAP FlexPod solution. You are using VMware ESXi 6 and FCP as the storage protocol.
In this scenario, which MPIO setting would you use on the ESXi host?
- A. fixed path with array preference
- B. fixed path
- C. round robin
- D. most recently used
Answer: C
NEW QUESTION 83
A customer wants a newly deployed UCS C-Series server's fans to run at the minimum speed required to keep the server cool. The customer is also complaining that the server fans are making too much noise.
In this scenario, which type of fan speed should you select under the Power Control Policy of UCSM?
- A. Max Power
- B. Low Power
- C. Performance
- D. Balanced
Answer: D
NEW QUESTION 84
What management solution can provision all three components of a FlexPod (NetApp storage, Cisco UCS compute and Cisco Nexus network)?
- A. NetApp OnCommand Insight
- B. Cisco UCS Director
- C. Cisco UCS Central
- D. Cisco FlexPod Manager
- E. NetApp FlexPod Manager
Answer: B
NEW QUESTION 85
Exhibit:
An administrator is building a FlexPod configuration with UCS 6296 Fabric Interconnect devices that support legacy Fibre Channel 9FC) connections. The administrator uses UCS Manager to configure the unified ports on the Fabric Interconnect.
Referring to the exhibit, how many ports will FC use after the configuration is completed?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: B
NEW QUESTION 86
An administrator is trying to present an NFS datastore to an ESXi host.
Which two must be available before mounting? (Choose two.)
- A. export policy access
- B. junction path case sensitivity
- C. host name case sensitivity
- D. datastore name case sensitivity
Answer: A,C
NEW QUESTION 87
An administrator has a FlexPod solution and is using OnCommand Unified Manager and OnCommand Performance Manager to monitor the FlexPod environment. Full integration has previously been configured between the two OnCommand virtual appliances; however, new performance issues are not being seen in the OnCommand Unified Manager dashboard.
In this scenario, which two settings should the administrator verify? (Choose two.)
- A. Ensure that the Event Publisher user credentials are entered correctly on the OnCommand Performance Manager appliance.
- B. Ensure that OnCommand Performance Manager is licensed for use with OnCommand Unified Manager.
- C. Ensure that the NetApp cluster is configured to forward SNMP data to OnCommand Performance Manager.
- D. Ensure that network connectivity exists between the two virtual appliances.
Answer: A,B
NEW QUESTION 88
To install your VEM, what is the extension of the VEM file name you'll be looking for to complete this install?
- A. .vem
- B. .vib
- C. .vsm
- D. .zip
Answer: B
NEW QUESTION 89
Your customer has the storage configuration for a FlexPod solution shown below.
- FAS8040 HA-pair
- Disk stack one-4x DS4243 disk shelves (2TB SATA disk drives)
- Disk stack two- 2x DS 2246 disk shelves (1.2TB disk drives)
- There are no unused SAS ports on either controller
- There are no expansion slots available on either controller
The customer wants to attach a single DS2246 disk shelf with 800 GB SSD drives.
In this scenario, what are two ways to connect the new shelf for optimal performance? (Choose two).
- A. Cable the new shelf to the end of stack one.
- B. Cable a new stack for the SSD shelf.
- C. Cable the new shelf to the beginning of stack two.
- D. Cable the new shelf to the end of stack two.
Answer: B,C
NEW QUESTION 90
While working on a performance related issue on your FlexPod solution, you notice an unequal distribution of traffic over the physical interfaces of a four port vPC between two Nexus 5000 switches. You would prefer a more even traffic distribution.
Which command would you use to accomplish this task?
- A. ~lacp system-priority~
- B. ~port-channel load-balance ethernet~
- C. ~lacp rate fast~
- D. ~hardware multicast hw-hash~
Answer: B
NEW QUESTION 91
Which set of commands maps VLAN 100 to VSAN 100?
- A. Nexus 5000-A#configure terminal Nexus 5000-B (config) # vsan database Nexus 5000-A (config)# vsan 100 Nexus 5000-A (config-vsan) # fcoe vsan 100
- B. Nexus 5000-A#configure terminal Nexus 5000-A (config) # vlan 100 Nexus 5000- A (config-vlan_ #fcoe vsan 100
- C. Nexus 5000-B# configure terminal Nexus 5000-B(config-vsan) # vlan 100 Nexus 5000-B (config-vsan)# vsan 100 name vsan100
- D. Nexus 5000-B# configure terminal Nexus 5000-B (config) # vsan database Nexus 5000-B (config-vsan)# vsan 100 Nexus 5000-B(config- vsan) #vsan 100 name FCoE-VLAN 100
Answer: B
NEW QUESTION 92
A customer asks you to configure QoS on a Cisco Nexus 7000 Series switch within a FlexPod solution.
Which three steps are required to accomplish this task? (Choose three.)
- A. Perform a shut/no shut on the affected interfaces.
- B. Attach policies to logical or physical interfaces and VSANs.
- C. Define traffic classes.
- D. Associate policies and actions with each traffic class.
- E. Attach policies to logical or physical interfaces and VLANs.
Answer: B,C,D
NEW QUESTION 93
You are asked to install the Virtual Supervisor Module (VSM) software on a Nexus 1000v switch.
Which two sources would you use to install this software? (Choose two.)
- A. VSC plug-in
- B. PXE boot
- C. ISO image
- D. OVA file
Answer: B,C
NEW QUESTION 94
......
Authentic Best resources for NS0-176 Online Practice Exam: https://www.actualcollection.com/NS0-176-exam-questions.html