[Jan 18, 2022] Latest CCNP Enterprise 300-420 Actual Free Exam Questions
CCNP Enterprise 300-420 Dumps Updated Practice Test and 148 unique questions
Topics of Cisco 300-420 Exam
The Cisco 300-420 certification exam validates the students’ knowledge of enterprise design. It covers a wide range of subject areas, such as advanced addressing & routing solutions, security services, WAN, advanced enterprise campus networks, SDA, and network services. The breakdown of these topics into the components of skills to be measured in the test is as follows:
Advanced Routing and Addressing Solutions
About 25% of the exam content is covered in this domain, and the candidates have to perform their skills in the following tasks:
- Developing the scalable, stable, and secure routing design for EIGRP, IS-IS, BGP, OSPF.
- Creating the structured addressing strategies for both IPv6 & IPv4;
#3 - Become Part of Cisco Community
Cisco is one of the largest networking service providers that has a global presence. This has helped such a company develop a wide community so every 300-420 exam-taker is advised to join it. In all, this community has millions of active certified, aspiring, and in-job professionals. Thus, the exam-takers can seek help from the Cisco community related to any problem, know the latest IT trend, take suggestions from in-service specialists, and share the struggle with fellow test-takers.
NEW QUESTION 22 
Refer to the exhibit. An engineer is designing a BGP solution for a client that peers with ISP1 for full Internet connectivity and with ISP2 for direct exchange of routes for several third parties. Which action, when implemented on the edge routers, enables the client network to reach the Internet through ISP1?
- A. Apply the AS-path prepend feature for ISP2.
- B. Advertise a default route for downstream routers within the client network.
- C. Apply route filtering such that the client advertises only routes originated from its own AS.
- D. Run an eBGP session within different VRFs for each ISP.
Answer: B
NEW QUESTION 23 
Refer to the exhibit. An engineer is designing an OSPF network for a client. Requirements dictate that the routers in Area 1 should receive all routes belonging to the network, including EIGRP, except the ones originated in the RIP domain. Which action should the engineer take?
- A. Make area 1 a standard OSPF area.
- B. Make area 1 a NSSA.
- C. Make area 1 a stub.
- D. Make the area 1 routers part of area 0.
Answer: C
NEW QUESTION 24
A network solution is being designed for a company that connects to multiple Internet service providers.
Which
Cisco proprietary BGP path attribute will influence outbound traffic flow?
- A. Community
- B. AS Path
- C. Weight
- D. Local Preference
- E. MED
Answer: C
NEW QUESTION 25
An engineer is working for a large cable TV provider that requires multiple sources streaming video on different channels using multicast with no rendezvous point.
Which multicast protocol meets these requirements?
- A. any-source multicast
- B. BIDIR-PIM
- C. PIM-SSM
- D. PIM-SM
Answer: C
NEW QUESTION 26
Which design consideration must be made when dual vEdge routers are deployed at a branch site?
- A. Configure BFD between vEdge routers to detect sub-second link failures.
- B. HSRP priorities must match the OMP routing policy to prefer one vEdge over the other.
- C. Use BGP AS-path prepending to influence egress traffic and use MED to influence ingress traffic from the branch.
- D. Traffic must be symmetrical as it egresses the vEdges and returns from remote sites for DPI to function properly.
Answer: C
NEW QUESTION 27
Which design element should an engineer consider when multicast is included in a Cisco SD-Access architecture?
- A. PIM SSM must run in the underlay.
- B. Rendezvous points must be used in a PIM SSM deployment.
- C. Multicast traffic is transported in the overlay and the EID space for wired and wireless clients.
- D. Multicast clients reside in the underlay, and the multicast source is outside the fabric or in the overlay.
Answer: D
NEW QUESTION 28
An engineer must propose a solution for a campus network that includes the capability to create multiple Layer 3 virtual networks. Each network must have its own addressing structure and routing table for data forwarding. The solution must be scalable to support hundreds of virtual networks and allow simple configuration and management with minimal administrative overhead. Which solution does the engineer recommend?
- A. multihop IPsec tunneling
- B. multihop MPLS core
- C. hop-by-hop VRF-Lite
- D. hop-by-hop EVN
Answer: D
NEW QUESTION 29
Which control-plane technology allows the same subnet to exist across multiple network locations?
- A. VXLAN
- B. FabricPath
- C. LISP
- D. ISE mobility services
Answer: A
Explanation:
Section: WAN for Enterprise Networks
NEW QUESTION 30
Drag and drop the characteristics from the left onto the YANG modules they describe on the right. Not all options are used.
Answer:
Explanation:
NEW QUESTION 31
Refer to the exhibit.
Which two solutions maximize the use of the links between the core and distribution layers? (Choose two.)
- A. use multiple equal-cost links
- B. use HSRP
- C. use RPVSTP+
- D. use an IGP
- E. use multiple unequal-cost links
Answer: A,D
NEW QUESTION 32
The implementations group has been using the test bed to do a 'proof-of-concept' that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address.
Use the supported commands to isolated the cause of this fault and answer the following questions.
The fault condition is related to which technology?
- A. NTP
- B. IPv4 OSPF Redistribution
- C. BGP
- D. IPv4 layer 3 security
- E. IPv4 OSPF Routing
- F. IPv6 OSPF Routing
- G. IP NAT
Answer: E
Explanation:
On R1, for IPV4 authentication of OSPF the command is missing and required to configure------ ip ospf authentication message-digest
NEW QUESTION 33 
Refer to the exhibit. Area 10 is a regular OSPF area and networks 10.1.1.0/24 and 172.16.1.0/24 are internal.
Which design provides optimal routing between both networks when the link between routers C and E fails?
- A. Move the link between routers C and D to area 10.
- B. Create a tunnel between routers E and F in area 10.
- C. Make area 10 a not-so-stubby area.
- D. Create an OSPF virtual link between routers E and F.
Answer: A
NEW QUESTION 34
Which NETCONF operation creates filtering that is specific to the session notifications?
- A. <create-subscription>
- B. <logging>
- C. <notification>
- D. <commit>
Answer: A
NEW QUESTION 35
An engineer uses Postman and YANG to configure a router with:
Which get-config replay verifies that the model set was designed correctly?
- A. Option A
- B. Option C
- C. Option B
- D. Option D
Answer: D
NEW QUESTION 36
Drag and drop the characteristics from the left onto the YANG modules they describe on the right. Not all options are used.
Answer:
Explanation:
NEW QUESTION 37
Refer to the exhibit. The full EIGRP routing table is advertised throughout the network. Currently, users experience data loss when any one link in the network fails. An architect optimizes the network to reduce the impact when a link fails. Which solution should the architect include in the design?
- A. Reduce the default EIGRP hello interval and hold time
- B. Run BFD on the inter links between EIGRP neighbors.
- C. Summarize the access layer networks from each access layer switch toward the aggregation layer
Answer: B
NEW QUESTION 38
......
Certification Path
To earn the CCNP Enterprise certification, the applicant first needs to take one core exam that is 350-401. It mainly focuses on one's knowledge related to network assurance, automation, security, infrastructure, architecture, and virtualization.
Once aced that test, the candidate can choose the concentration exam from the set of six options, and Cisco 300-420 is one of them. Moreover, by passing this exam, you are qualified for the Cisco Certified Specialist – Enterprise Design certification. The rest of the offered tests focus on advanced routing and services, designing and implementing wireless networks, SD-WAN, and automation solutions.
Verified 300-420 dumps Q&As - 100% Pass from ActualCollection: https://www.actualcollection.com/300-420-exam-questions.html
Latest 100% Exam Passing Ratio - 300-420 Dumps PDF: https://drive.google.com/open?id=1C6BcIwBoCL09WLxMFYYtrvT-afbq018p